Category: Latest Updates

Latest Updates

Tips For Repairing an Electric Dryer

No Comments

Clothes dryers are used almost in all homes for drying clothes. So if it stops working it causes anxiety and disturbs all the daily routines as you might have to dry clothes with hands until it will be repaired by a dryer repair specialist. However, some of the most common problems that are often seen with cloth dryers are that they run properly but do not dry cloths. The reason for not drying cloths is due to the absence of heat which occurs if heating system does not work properly.

If the dryer works fine without electric heating and air drying load of clothes, the problem is probably a failed heating system. To determine whether the failed component, unplug the dryer for proper inspection samsung dryer repair pasadena.

First cautiously remove the heating component from the dryer. It is very simple procedure but you have to take necessary precaution. There is an electrical connection to disconnect and there may be resistance screws in place.

After removal of the device controls the coils should be inspected for breaks. These coils seem like a huge version of an electric bulb. They become heated when power is applied to them. The heat will finally cause breakage of a coil, like a lamp, its filament is broken. Sometimes you can see the break in the coil. Sometimes it is useful to check the coil with the electricity meter. Adjust the meter to compute resistance or ohms., brings meter wires to both ends of the coil. If infinite ohms are measured as the meter shows a break in the coil. If the device measures the limited amount of resistance, where resistance is in good working condition and repair is not covered by this procedure

If you find that your heating component is broken then you should check the model of your dryer and buy the broken part of the heating system of dryer. You can easily find this part from local appliance parts suppliers or you can search internet for further help.

Once you acquire the substitute part of dryer then unlock the screws and fix the new heating element in the dryer heating system. Before installing the new part check it with the meter for proper functioning. If the new part point to an open circuit, which indicates that the heating component is working properly.

Categories: Latest Updates

What Should I Look for in an Appliance Repair Professional?

No Comments

Malfunctioning appliances are frustrating and inconvenient. When your fridge breaks down, your food can spoil. When your washing machine and dryer stop washing and drying, you have to wash clothes by hand, or take time out of your day to go to the laundromat. When your stove burners won’t light, you can’t prepare healthy, delicious meals for your family.

Luckily, most appliance repair experts can diagnose and fix these issues, regardless of what brand or model of appliance you have. But with the array of appliance repair companies out there, even in a small town, how can you choose the right technician? Think about what’s important to you. Do you need repairs immediately? Do you want the lowest price? Or do you simply want assurance that you’re getting the best possible repair service? All of these factors can help you select the appliance repair company that’s right for you kenmore appliance repair altadena.

Training and Experience

Perhaps you simply want the best possible appliance repair service. How can you know someone’s skill is superior in his field? Look online or ask for information about the technician’s training and experience. The longer a repairman has been in the industry, the greater the chance he’ll have seen your appliance’s issue before and will know exactly how to fix it. Similarly, if a technician has training or certification to work with your specific high-end brand or model, or affiliation with an appliance repair organization, you can probably trust him to have the knowledge and skill to do the job right.

Turnaround Time

Do you need refrigerator repair immediately because you’re hosting a large event at home tomorrow? Did you wake up to your washing machine leaking all over the laundry room floor, and it won’t stop? Sometimes your biggest repair consideration has to be how quickly a technician can come out to your property and resolve the issue. Some appliance repair companies offer same-day service. Others will come out in an emergency, no matter the time of day. You may have to call several companies before finding someone who can fit you in immediately, but they’re out there. Note, however, that if you need appliance repairs with a quick turnaround time, you may have to sacrifice some other criteria-speed might cost more, or might mean you can’t be choosy about qualifications.

Price

Are you working within a tight budget? You can certainly research appliance repair companies in your area and compare their prices, looking for the best deal. But as with same-day service, you may have to sacrifice a few other preferences in order to keep costs down. For instance, you might have to wait longer for an appointment, and go without your appliance for a week or more. Or you might have to work with a brand-new technician rather than someone with 20 years of experience. When you do find a washer/dryer, refrigerator, or oven repair professional who fits your budget, give the rest of his qualifications a scan. You don’t want to have to call for repairs again in a month because the person you hired at a cheap price did a shoddy job.

There are several other considerations you might want to take into account when choosing an appliance repairman. Does the company offer a warranty? How long does it last? Does it cover both parts and labor? Is the company licensed and insured? A trip to the company’s Web site should tell you these things, but if you don’t see the information you’re looking for, don’t hesitate to ask over the phone. If the company isn’t willing to tell you what you need to know to make an informed decision, look elsewhere.

 

Categories: Latest Updates

Equipment Restore: How Discovering an Equipment Restore Firm Can Save Cash

No Comments

One of the crucial irritating issues that may occur is when one in every of your home equipment breaks, particularly while you want that specific equipment to finish a process within the close to future. Most individuals have skilled that gut-wrenching second after they notice their garments have not dried, or after they attain right into a fridge and pull out a lukewarm can of cola. Equipment failure is only a reality of life, however thankfully, you do not have to utterly change your washer, dryer, dishwasher, fridge, or different machine. As an alternative, you’ll be able to have it repaired.

Whenever you transfer into a brand new dwelling or residence maytag appliance repair pasadena, one of many first issues it is best to do is search for a widely known, well-reviewed equipment restore firm. Write the corporate’s data down and preserve it in a secure place, maybe in a drawer, or caught to your fridge with a magnet. It is vital to have that data accessible as shortly as it may be ought to an vital equipment fail and desires serviced as quickly as attainable. You will not need any delays in between realizing that your equipment wants repaired and scheduling an appointment with an equipment restore firm.

Equipment restore can prevent a big sum of money. For starters, repairing your home equipment will help forestall the necessity to buy brand-new machines. Should you’re on a good price range, the acquisition of a brand new fridge, washer or dryer can actually set you again. Equipment restore may prevent cash in that one other potential downside may very well be found whereas your present subject is being mounted. This protects cash as a result of a restore specialist could make the restore on the spot with out having to be referred to as again for a separate go to later.

Should you’ve discovered equipment restore firm in your space, one factor you may wish to investigate cross-check is whether or not they have some sort of annual upkeep program. This could additionally aid you get monetary savings, as some firms will provide a per-repair low cost to those that enroll in such a program. Should you wind up needing a number of repairs over the course of a yr for just a few totally different home equipment, the price financial savings you’d see from being a part of an annual upkeep program may very well be vital.

Categories: Latest Updates

How to Repair Major Appliances

No Comments

The first thing you should understand is that your household appliances run off of your home’s electrical system. Large appliances often need a 220-240 volt wiring and cannot be used in your house’s standard 110-120 volt circuits. However, all appliances have their power requirements written in the owner’s guide or on the appliance itself.

Large household appliances are fairly complex machines Appliance Repair Van Nuys, so sometimes it can be unclear what has caused the problem. The first step to finding out where the malfunction is to decide whether it is in a mechanical device or a control device. Let’s take a dryer for example, the control parts control the heat, and the mechanical devices control the drum. So if the drum tumbles, but the dryer does not heat, then you are looking at a control problem. On the other hand, if the dryer heats up, but it doesn’t tumble, then you are looking at a mechanical problem. In most large household appliances you can use this method to find out where your problem is located.

Now, before you begin to repair your appliance you will need to keep three very important tips in mind. Always double check that your appliance is disconnected from the power outlet and from any gas supply. Most appliances are held together with various screws and bolts. However, if any of the parts are held together with a weld or rivets you should not try to repair the appliance yourself – call a serviceman. Also, broken parts can be replaced more easily than trying to repair them either yourself or by a professional. Replace any worn parts – you can usually find a replacement by looking up your model number online. Always refer to the owner’s manual if you are installing the part yourself.

The first task of how to repair major appliances is to check if it is connected to the power outlet. It may sound dumb, but with washers it is especially common to find that they have “walked” or wiggled themselves away from the wall and they come unplugged that way. Sometimes the power outlet itself is not getting power, and you can easily test this by plugging in something into that outlet and see if it works. Check to see if any fuses or circuits have blown too. If your appliance uses gas or water, check to make sure they are receiving a sufficient supply. Don’t forget that you can always check the owner’s manual for helpful information and troubleshooting for your appliance.

Next, I’ll go over how to properly and safely disassemble your appliance, and how to put it back together once you have completed the repair. You should refer your owner’s manual for the assembly diagrams and instructions. Remember that you will have to put your appliance back together again so you should keep a bucket nearby for screws and bolts, and lay out the parts in the order in which you removed them. If you will be disconnecting any wires, label them so you know where they go. Begin with removing the knobs and other fasteners. Most knobs just pull right off of the shaft, and some others you can twist off, others are held on by pins or clips. The housing panels are usually held together by screws, or held in place by clips. Never try to force parts apart, look for hidden fasteners. Sometimes fasteners can be hidden under a company logo or nameplate, under a plastic plug, or at the bottom of the appliance. Before reassembling a major appliance, vacuum the inside and remove all the lint and dust. Check for any other problems and make any adjustments or repairs. If the appliance uses a motor, lubricate it and make sure electrical contacts are clean. Reassemble the appliance in reverse of the way you took it apart. Never force parts together, or tighten the fasteners too much. Make sure any moving parts don’t bind. After you put your appliance back together, connect the power and turn it on. If your appliance overheats, makes weird noises, smells, or doesn’t work, turn off the power and do a once over of your repair again.

In summary, if you follow these tips on how to repair major appliances you will save a ton of money by doing the repairs yourself, and also you will get a better understanding of how your appliance works.

Categories: Latest Updates

What You Need To Know About Appliances

No Comments

The huge strides taken by the electronic goods industry in the last decade or so has made available a mind-boggling array of appliances to consumer nowadays.

Regardless of whether one is in one’s offices or at home Whirlpool Appliance Repair Los Angeles, a causal look around reveals the astonishing number of appliances that have become a part and parcel of our daily life. The refrigerator, the microwave oven, the food processor, the toaster, the coffee maker, the cooking range, the dishwasher, the washing machine, the steam iron, the AC, the plasma television, the VCD, the CD player, the home theater, the laptop, the desktop, the Xerox machine, the printer, the fax machine, the paper shredder, the fancy mobile phone handset, the PDA, the calculator – stuff like that is all around us all the time. In fact, we are so dependent on these fancy gadgets that it is difficult to visualize living without them.

However, it is not enough to just have knowledge of the latest kinds of appliances or the various brands. It is important to know the advantages a particular brand might have over another and exercise an informed choice when purchasing any appliance. It is even more important to keep in mind the various safety standards and not be swayed by glitzy advertising when making a purchase.

It is always better to pay a little more for an appliance to make sure that you are getting a product that will last and is hazard-free. Moreover, most products come with a guarantee/ or warranty. Be sure to save all documents relating to your purchase in case it needs replacement or repairs.

Categories: Latest Updates

Most Common Problems on Smart Drive Washing Machines

No Comments

The First Smart Drive washing machines by Fisher & Paykel came out of production in 1991 and since then we have experienced 8 improved and more sophisticated models. Although they differ a lot, the most common faults are very similar. From our long experience, we can say that almost 80% of them have minor faults, but are still worth repairing. We will try to cover all of them.If you find that yours is different, it may be some combination of few covered Washer Repair Los Angeles.

NO POWER

This fault can be caused by failure of one of the major electrical parts: motor, pump, rotor positioning sensor, reed switch, display panel or one of the water valves. Also, cause can be in the motor controller itself. It can be burned by water related short cut or by power surge.

On the “phase 4″( models 085, 058, 508, 608, 708) motor controller there is a mode where it can shut down in the event of a transient on the mains. What does this means is that machine will go in “asleep” mode and the module will not restart unless the power is turned off at the wall for at least 90 seconds.

On the “phase 5” (models 095-Fresh, 059-Pride, 509-Excellence, 609, 709) pump is considered as a part of the power supply. If it is disconnected (thermal cut out tripped which can be caused by pump blockage) washing machine will be dead.

Repair of this fault is quite expensive and vary between models from $100 to $250.
Best way to prevent it is to do regular inexpensive service checks of all major parts and empty pockets before wash. If you buy used washing machine try to arrange cleaning, water blasting and sanitizing services which will free drum and bowl from all dirt that can cause pump blockage.

LEAKING

This is most common washing machine problem and in some cases it is related to real technical issues and sometimes to misuse or wrong installation.

Easy to notice leaks are from water taps, inlet hoses, hot or cold water valves, water mixing chamber. Leak from top end of the drain hose is also easy to notice and usual spot is close to the connection to the body of the machine.

Leaking from the pump is almost always caused by poorly secured pump bracket; pump’s
diaphragm and pump itself are last causes for the leak. Next possible leak spot is an air bell.

If water level is not set properly and water is filled over HIGH mark on the agitator, splashing may cause some “leak”. Over filling may be caused by bad (dirty or punched) pressure pipe. Clothes overloading can make same problem.

Broken neck ring and damaged plastic inner bowl are another possible reasons for leak as well as too much detergent used.

Fixing of leak related problems should not(except damaged inner bowl and leak from main seal) be very expensive, up to a $100 most.

WASHING MACHINE IS NOISY

Noise can be related to few different sources, some of them indicating that machine have to be serviced or repaired to avoid major damage.

If washing machine is very noisy during spin cycle main seal and bearing are bad. This fault has to be fixed urgently, otherwise water leak can damage motor and rotor positioning sensor.

Banging sound is usually related to drain hose, inlet hose, mains lead or harness. They are either loose or washing machine has not been leveled properly. This can not cause some other bigger problem but could be very annoying.

Another banging sound can be caused by inner and outer bowl hitting machine’s body.
The reason for that is that water somehow escaped from two balance rings in the inner bowl. Same problem can be caused by overloading or uneven clothes arrangement in the bowl.

Pump can be source of very annoying noise. This noise starts on the beginning of the spray/deep rinse or spin cycle and lasts until pump empties water. It has been caused by rusted pump stator (water or humidity damage) or ex center rotor position. CRC spray will fix the problem temporary and new pump will save machine from more expensive faults(burned pump will burn triac on the motor controller).

Also cracked or chipped rotor magnets can cause some grinding noise.

To fix noise problem you may expect anything between $50 to $350.

WASHING MACHINE IS “DOING NOTHING”

First cause of this fault can be in reed switch(lid and off balance switch). Broken switch should be replaced to avoid motor controller failure.

Water taps can cause this problem also. Water should be connected and taps should be on.

If delay start is on, Strat/Pause switch will not respond.

When Auto Level has been used machine will resense water level every time the lid is opened.

SIPHONING

This problem is related to the natural law. Usually standpipe height is too low. Minimum height should be 850mm from the floor. Top of the drain hose should be placed through “U” shaped hose guide not more than 2cm from the top of the guide. If drain hose is pushed too far into the standpipe or drain, washing machine will empty(siphon) water during fill or rinse cycle.
Siphoning can be caused also by restricted drain hose or partial pump blockage.

Categories: Latest Updates

DIY Repair On Your Refrigerator

No Comments

It’s no at all uncommon to see your refrigerator functioning great and then you suddenly notice come, well you would not come close to calling them malfunctions, but yeah, it seems like suddenly your refrigerator is not functioning great anymore. What should you do? Most people will call the repairman and pay for their services. Some will just ditch the fridge and buy a new one Jennair Appliance Repair.

The second option is not at all practical, unless your refrigerator is like 10 years old and have been showing signs of age already. Nonetheless, if this is not the case, don’t replace your fridge right away. The first option is actually very common; when we encounter problems with the refrigerator, or any other appliances, it seems that the most sensible thing to do is to call for help.

But why pay for these repair service when you could repair the refrigerator yourself? Seems impossible? Many people have actually been doing do-it-yourself repair works on their refrigerator so you can do it, too. You need not be an expert on handling appliances; all you need to do is follow these simple guidelines.

My fridge is not cool!

A typical refrigerator should have a temperature of 38 to 40 degrees Fahrenheit in order to store and preserve your food properly. A warm refrigerator is not a problem to ignore as this may cause your food to spoil. If this happens, check the thermometer inside the refrigerator. The first thing you can do is adjust the temperature through the thermometer.

Wait for the temperature to gradually set in but if after 6 hours and the temperature still did not change, check the fan. If the fan runs just fine, check the condenser coils, which may be located at the front while most are found in the back. To check the condenser coils, remove the cover and using a vacuum cleaner, remove the dust and dirt. You can also use a stiff brush or you may prefer to wash them with soapy water, especially if the dirt has hardened or are greasy.

Another reason for the warm temperature may be that you haven’t defrosted lately, especially if your fridge needs to be manually defrosted. If so, defrost the refrigerator by turning it off and removing all the food items inside the freezer and refrigerator. Leave the freezer and refrigerator door open overnight. In the morning, replace the food, turn the fridge on and put the thermostat on a middle setting.

If you have done all the things above and still find your refrigerator warm, it may be time to replace your door seal. Broken door seals fail to seal in the cool air and allows warmer air from outside to enter. You can test you door seal by placing in a piece of paper on the door seal and then close the door. If you can remove the paper easily, then that is a sign your door seal is not working well.

Leaks and puddles on the floor

A common refrigerator problem, water that leaks from the refrigerator down to your floor may come from different sources and different causes. One of the most likely reason is that the lines of the water and/ or ice dispenser of the fridge are broken. These broken lines may have to be replaced. That may be the cause for leaks unless of course, you do not have water dispenser on your fridge.

Another cause of leaks may be the defrost tray or drain pan underneath the refrigerator. If you fridge has this, check it for damages, cracks and even holes. After that, clean the drain tube which can be located in the floor of the fridge or at the back. Pour a mixture of hot water and bleach through the opening using a turkey baster. After cleaning, empty the drain pan of water.

Finally, leakage and water spills may come from a clogged drain in the freezer. If this happens, you can usually find the water dripping from the ceiling of your refrigerator (if your fridge has the freezer on top of the body). If this is the case, the solution is to unclog the drain the freezer or to dry the insulation by removing first the divider of the fridge and the freezer.

Noisy neighbors, noisy fridge

Another very common problem that you can fix yourself is the noise coming from your fridge. Many people will often ignore and even dismiss this problem, thinking that the sounds are just signs that the motor is working. On the other hand, these noise we hear may be a sign of something else, and that there may be something wrong with your fridge.

Like water spills and leakage, these noises may also come from different sources. However, the most common source is from the inside of the fridge. When this happens, it is probably the fan that is causing it. If your refrigerator is quite old, the fan will omit noise, which may vary from chirping to squealing to full out groaning. If the noise becomes too loud, it may be a sign that your fan is already worn down and may need to be replaced.

Categories: Latest Updates

Appliance Repairs, Parts, and Service

No Comments

When repairing your appliances, it is important to pick a reliable professional company to take care of your needs and get the job done right. You may want to find a service company who can repair all your appliances with one stop. Some companies may have a repair service for dishwashers, washing machines, dryers, stove etc. It is always recommended to shoot for a repair service before replacing an appliance.

When looking for an appliance servicing Whirlpool Appliance Repair Los Angeles, you also want to make sure that they are knowledgeable in many different brands as some brands require special treatment or parts. A good company should be able to tend to each appliance brand uniquely. Some service companies treat each appliance the same and may end up damaging your belongings.

Some appliance shops may also sell parts. If you find a place that can do that for you they also may provide information for you to fix it yourself. Generally, it is easy to just buy the parts at the store but if they don’t have the piece you need in stock these companies may be able to order one for you and ship it right to your house.

There are some preventative tips for saving your appliances. Refrigerators need to be set to 65 degrees or more and the condenser coils should be cleaned as to not over run the refrigerator. Dishwashers are easy. Don’t let chunks of food go through a wash. If there is a film on your glass ware, run an empty load through until the soap back up is cleared. With ovens all you have to do is try not to open the oven door while it is being used. This causes the oven to work harder to keep up with temperatures. In use, an oven should not have a drip pan lined with aluminum foil. Doing this is setting yourself up for flakes of dried out food and aluminum foil to get into the plug in receptacle. Before having a big gathering, run the self cleaning on the device.

Appliances are easy to maintain and fix when you take care of them properly. With the right knowledge you can lengthen the life of your appliances with no problems. Avoiding repair is always a financial plus but when the time comes for repair make sure you have a professional service company on file that fits your needs in a professional manor.

Categories: Latest Updates

Refrigerator Repair When You Need It

No Comments

No one knows when refrigerator repair might suddenly become a necessity. With some people’s luck it might happen on a weekend of a party or some other large event when the refrigerator is full of perishable foods. Whatever the scenario, no time is really a good time. That is why it is always good to plan ahead for possible problems. It might be helpful to have a refrigerator repair company on hand in case of a problem.

Most places probably do not specialize in refrigerator repair Refrigerator Repair Los Angeles. Most likely someplace that could fix this appliance would also be able to fix other appliances. You never know how many times you might end up calling them for a variety of appliances in your home. You might be thinking it strange to do a lot of research for one appliance. The reality is you might use the number more than you expect.

When you begin your search for an appliance shop that does repairs, think about what is important to you. To most people, customer service, availability, trustworthiness, and cost are four important areas to consider.

You will probably find a few appliance shops in your area. Take the time to call each, and after that first call you might know the answer to the first trait. You will likely know whether they have good customer service. If the company has a website, you should be able to find out their availability easily. You should look for one that offers night, weekend, and emergency appointments. This is important because your food will only stay cold so long. Finding an appliance company that is trustworthy is also important. Your home is your property. You will want to make sure that the technicians coming into your home are safe and reliable. They should leave your home in better condition than how they found it. Cost is another consideration. Just make sure they are within your budget and that they offer financing if you need it.

After you look at these four areas, you are on your way to having an appliance store that you can call whenever a problem comes up whether it is refrigerator repair or repairs for your washing machine. Taking the time now to do the research and find the right place will save you time later, and most likely you will end up with a good choice since you did have more time. Since you have the time, it might be a good idea to check up on the companies you are considering on review sites on the internet and even with friends and family.

Categories: Latest Updates

Dryer Troubleshooting Versus Professional Appliance Repair Services

No Comments

A broken or poorly working dryer can bring your whole home-life to a screeching halt. Suddenly, your railings and chair backs are populated with t-shirts and jeans hung out to dry, and all the necessary uniforms, work clothes, and towels that you use every day aren’t on hand when you need them. Don’t let this madness go on any longer than necessary. Find out what you can do to troubleshoot some common dryer problems, and when you should call a pro for appliance repair service Dryer Repair Los Angeles.

The first and most important guideline to DIY appliance care is: if you’re not comfortable tackling it on your own, call a pro. There’s no sense making yourself nervous or doing something that feels unsafe. If the very thought of delving into the workings of your dryer makes you break out in a sweat, put the dryer repair manual down and pick up a phone. There’s no shame in calling a professional when you
need to.

If you’re ready to get your homegrown troubleshooting skills going, keep that repair manual to hand and dive in. Take a common and fairly dramatic scenario: your dryer stops working altogether. No matter what buttons you push, nothing happens. The first thing to check is the door. Almost all dryers have a door latch safety feature that has to be engaged before the machine will start. Shut the door firmly to make sure it’s latched properly and see if that helps.

If the door latched but still nothing happens, then it’s time to check the reset switch. This is a prime troubleshooting solution especially if your dryer has recently been running. The machine may simply have overheated. Wait about ten minutes for things to cool down, then consult your manual to find out where the reset switch is. It’s often on the control panel. Make sure you disconnect the power supply before rooting around for the reset switch and shut off the gas supply valve, if applicable.

If checking the door latch and the pushing reset switch don’t do the trick, there’s probably an issue with one of the individual parts of the dryer. If you’re comfortable and want to pursue the next dryer repair step on your own, you can disassemble the unit and check out which part is at fault. You can refer to the manual and look online for repair guides and helpful diagrams to assist you.

If the idea of going into the dryer’s innards fills you with fear, though, it’s time to call your local appliance repairs company and tell them what the problem is. These folks are professionals for a reason. They know the ins and outs of these machines and will know what to do to get your dryer back on its feet.

Categories: Latest Updates